<div dir="ltr">Rick,<div><br></div><div>I do quite a few JST crimps and here is what I found works best for me. Note I have tried every crimper I could find, the engineering ones and others. I found the process of setting up the terminals to be the key to success. It is not a fast process but I have had good results. </div><div><br></div><div>I use this crimper, but many are the same:</div><div><img src="cid:ii_lxwda5s40" alt="image.png" width="290" height="163" style="margin-right: 0px;"><br></div><div><br></div><div>Then I prepare the terminal, first cut off the leader near the terminal to be used: </div><div><img src="cid:ii_lxwdb9ax1" alt="image.png" width="562" height="256"><br></div><div><br></div><div>Bend the terminal to be crimped 90 degrees as shown below: </div><div><img src="cid:ii_lxwdbx0x2" alt="image.png" width="562" height="522"><br></div><div><br></div><div>Insert into the crimper and close as shown, these crimpers lock in this position and often the insulation wings are a bit wide and I have to squeeze them before installing in the crimper.</div><div><img src="cid:ii_lxwddelm3" alt="image.png" width="562" height="481"><br></div><div>Then I insert the stripped wire. </div><div><img src="cid:ii_lxwdeee64" alt="image.png" width="562" height="490"><br></div><div><br></div><div>After the crimp I break the terminal and wire from the leader, while doing a pull test. </div><div><img src="cid:ii_lxwdf8ae5" alt="image.png" width="545" height="562"><br></div><div><br></div><div><br></div><div>Trampas</div><div><br></div><div><br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Wed, Jun 26, 2024 at 5:37 PM Rick DeNatale via TriEmbed <<a href="mailto:triembed@triembed.org">triembed@triembed.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="auto"><div dir="ltr">I’m convinced that these things are the invention of the devil!<div><br></div><div>Despite my best efforts, I’d guess i have about a 20% yield crimping JST terminals.</div><div><br></div><div>I’ve bought several crimping tools. <a href="https://www.amazon.com/gp/product/B01N4L8QMW/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1" target="_blank">https://www.amazon.com/gp/product/B01N4L8QMW/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1</a> and <a href="https://www.amazon.com/gp/product/B078WNZ9FW/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1" target="_blank">https://www.amazon.com/gp/product/B078WNZ9FW/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1</a> were recommended by various YouTube videos.</div><div><br></div><div>The second one works a bit better unlike the first it has you crimp the electrical contact first and then the mechanical crimp around the insulation. </div><div><br></div><div>My big problem is that the insulation crimp often doesn’t form correctly. Instead of wrapping around the insulation the wings just stick out straight.</div><div><br></div><div>Then either the terminal comes off the wire while removing the “tape” part, or when trying to to insert the terminal in the plastic shell.</div><div><br></div><div>Is my problem with the terminals? I’ve been buying kits from Amazon. Would i be better off with a different vendor like Digikey?</div><div><br></div><div>Any advice gladly appreciated.</div><div><br id="m_2782960289359806266lineBreakAtBeginningOfSignature"><div dir="ltr">——<div>Rick DeNatale</div></div></div></div></div>_______________________________________________<br>
Triangle, NC Embedded Interest Group mailing list<br>
<br>
To post message: <a href="mailto:TriEmbed@triembed.org" target="_blank">TriEmbed@triembed.org</a><br>
List info: <a href="http://mail.triembed.org/mailman/listinfo/triembed_triembed.org" rel="noreferrer" target="_blank">http://mail.triembed.org/mailman/listinfo/triembed_triembed.org</a><br>
TriEmbed web site: <a href="https://TriEmbed.org" rel="noreferrer" target="_blank">https://TriEmbed.org</a><br>
To unsubscribe, click link and send a blank message: mailto:<a href="mailto:unsubscribe-TriEmbed@bitser.net" target="_blank">unsubscribe-TriEmbed@bitser.net</a>?subject=unsubscribe<br>
Searchable email archive available at <a href="https://www.mail-archive.com/triembed@triembed.org/" rel="noreferrer" target="_blank">https://www.mail-archive.com/triembed@triembed.org/</a><br>
<br>
</blockquote></div>