<div dir="ltr"><div><br></div><div><b><i>As everyone responds, please include Adam (Adam Novak <<a href="mailto:interfect@gmail.com" target="_blank">interfect@gmail.com</a>>) in your "To:" addressing -- I don't think he is a member of the TriEmbed email list yet.</i></b><br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Fri, Oct 29, 2021 at 12:05 PM John Wettroth <<a href="mailto:jwet@mindspring.com">jwet@mindspring.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div style="overflow-wrap: break-word;" lang="EN-US"><div class="gmail-m_2164941829254684657WordSection1"><p class="MsoNormal"><span>The microstrip track with all the via fencing looks too narrow.<span>  </span>I assume this is supposed to be a 50 ohm line?<span>  </span>You might check this- I assume this is on FR4 at 1.5 mm (.062”), if so, a 50 ohm track is about 3 mm wide (.125”).<span>  </span>A narrower track will give you a higher impedance line, this line looks more like a 100 ohm line.<span>  </span>If it’s a matching section, ignore my comment, but if its supposed to be 50 ohms, check it.<span>  </span>You might also consider putting some via stitches around the perimeter of the planes- they’re kind of floating RF wise at the edges except perhaps at the top and at the fencing.<span>  </span>I’m sure your initial design will work as is- but the narrow track will create some mismatch loss (range) and the lack of perimeter stitching can cause RF leakage- kind of a slot antenna that will radiate in the plane of the board- could give a squirrelly radiation pattern.<span>  </span>If the module vendor has a recommended layout, I would study it carefully and use it as much as possible.<span>  </span>Also, is any local bypassing recommended external to the module on power lines, etc.?<span>  </span>Something like a 10 nF 0805 and a bulk 1 uF ceramic would seem wise and cheap.<span>  </span>That 3.3v line is an inductor- not so bad really but dying to have a shunt C at the module end to make a proper “bias T” kind of structure.<span>  </span>Have fun.<u></u><u></u></span></p><p class="MsoNormal"><span><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size:10pt">Regards,<br>John M. Wettroth<br>(984) 329-5420 (home)<br>(919) 349-9875 (cell) </span><span><u></u><u></u></span></p><div style="border-color:rgb(225,225,225) currentcolor currentcolor;border-style:solid none none;border-width:1pt medium medium;padding:3pt 0in 0in"><p class="MsoNormal"><b><span>From:</span></b><span> TriEmbed <<a href="mailto:triembed-bounces@triembed.org" target="_blank">triembed-bounces@triembed.org</a>> <b>On Behalf Of </b>Scott Hall via TriEmbed<br><b>Sent:</b> Friday, October 29, 2021 3:35 AM<br><b>To:</b> Triangle Embedded Computing Interest Group <<a href="mailto:triembed@triembed.org" target="_blank">triembed@triembed.org</a>><br><b>Cc:</b> Adam Novak <<a href="mailto:interfect@gmail.com" target="_blank">interfect@gmail.com</a>><br><b>Subject:</b> [TriEmbed] Does my Raspberry Pi LoRa modem board look ready to send off to OSHPark?<u></u><u></u></span></p></div><p class="MsoNormal"><u></u> <u></u></p><div><div><p class="MsoNormal">Question from Adam Novak <<a href="mailto:interfect@gmail.com" target="_blank">interfect@gmail.com</a>>, posed at 9:26pm 28-Oct-21:<u></u><u></u></p></div><blockquote style="border-color:currentcolor currentcolor currentcolor rgb(204,204,204);border-style:none none none solid;border-width:medium medium medium 1pt;padding:0in 0in 0in 6pt;margin:5pt 0in 5pt 4.8pt"><div><div style="margin-bottom:3pt;box-sizing:inherit;max-width:none;font-variant-ligatures:common-ligatures;font-variant-caps:normal;text-align:start;text-decoration-style:initial;text-decoration-color:initial;word-spacing:0px"><div><div><div><div><p class="MsoNormal" style="margin-bottom:12pt;background:white none repeat scroll 0% 0%"><span style="font-size:11.5pt;font-family:"Arial",sans-serif;color:rgb(29,28,29)">Anybody here know PCB design? Does my Raspberry Pi LoRa modem board look ready to send off to OSHPark?<br><span><img id="gmail-m_2164941829254684657Picture_x0020_1" src="cid:17ccce5f1465b006a1" width="566" height="494" border="0"></span><u></u><u></u></span></p></div></div></div></div></div></div></blockquote><div><p class="MsoNormal"><u></u> <u></u></p></div></div></div></div></blockquote></div><br clear="all"><br>-- <br><div dir="ltr" class="gmail_signature"><div dir="ltr"><div><div dir="ltr"><div><div dir="ltr"><div>Scott G. Hall<br>Raleigh, NC, USA<br><a href="mailto:scottghall1@gmail.com" target="_blank">scottghall1@gmail.com</a></div><i>Although kindness is rarely a job, no matter what you do it's always an option.</i><br></div></div></div></div></div></div>