<div dir="ltr"><div dir="ltr"><div dir="ltr"><div dir="ltr">Craig,<div><br></div><div>Power MOSFETs include a reverse bias body diode that will conduct on the negative half-cycles of the AC when used as an AC switch. To turn off the AC to the heater you would need to put two MOSFETs in series with one of them reversed. This would let them stop AC but you would still need to use higher voltage MOSFETS. The AC line's nominal 110 V rating is RMS (kind of the effective power delivery vs a DC signal of the same voltage). The actual peak voltage on the AC line is closer to 170 volts. You also cannot stack the voltage rating of the back-to-back MOSFETs because one of the body diodes will always be forward biased. So each diode must be able to tolerate 170V minus one body diode drop (0.6 V nominal). So you could use two MOSFETs rated for 200V wired back-to-back in series. You would want low Rds devices to reduce the power dissipation but they will be more expensive that your typical parts bin MOSFET. The MOSFET could do great PWM control but you would want to drive them with a opto-isolator with a photovoltaic output. The link below show's Digikey has 47 isolators (some multiple channel) in normal stock that would fit the bill. This would let you drive them with a microcontroller while keeping the microcontroller, and your computer and you isolated from the AC mains. </div><div><br></div><div><a href="https://www.digikey.com/products/en/isolators/optoisolators-transistor-photovoltaic-output/903?FV=ffe00387%2Ca400b4&quantity=0&ColumnSort=0&page=1&stock=1&nstock=1&k=opto+isolator&pageSize=500&pkeyword=opto+isolator">https://www.digikey.com/products/en/isolators/optoisolators-transistor-photovoltaic-output/903?FV=ffe00387%2Ca400b4&quantity=0&ColumnSort=0&page=1&stock=1&nstock=1&k=opto+isolator&pageSize=500&pkeyword=opto+isolator</a><br></div><div><br></div><div>Your SSR would work well or you could use a Triac for controlling the AC voltage. The SSR includes it's own internal opto-isolator but if you use your own Triac you would need to add a triac-output opto isolator. Digikey lists 513 triac opto isolators that would fit the bill. One issue difference between using MOSFETs verse a SSR or Triac though. The MOSFETs would have a very low power dissipation due to their low Rds when fully saturated. While a triac will have a fixed forward voltage (1-1.5V) and will dissipate V * I power when conducting. So at Triac conducting 5 amps would dissipate 5 to 7.5 Watts, where the pair of mosfets at 10 mOhms each, would dissipate 2W. The triac would be much cheaper though. </div><div><br></div><div><a href="https://www.digikey.com/products/en/isolators/optoisolators-triac-scr-output/904?k=triac+optoisolator&k=&pkeyword=triac+optoisolator&pv41=719&sf=0&quantity=&ColumnSort=0&page=1&stock=1&nstock=1&pageSize=500">https://www.digikey.com/products/en/isolators/optoisolators-triac-scr-output/904?k=triac+optoisolator&k=&pkeyword=triac+optoisolator&pv41=719&sf=0&quantity=&ColumnSort=0&page=1&stock=1&nstock=1&pageSize=500</a><br></div><div><br></div><div>On other thing to watch is that removing the fan motor from the auxiliary heater circuit means that heater will see 16 volts higher than it's design specification and would dissipate around 37% more power. You may want to avoid driving the axuulary heater at 100% duty. You can either use a rheostat or just PWM at a reduced duty cycle. </div><div><br></div><div>(110^2)/(110-16)^2</div><div><br></div><div>I look forward to reading about your experiments</div><div>Shane</div><div><br></div><div><br></div><div><br></div><div><br></div></div></div></div></div><br><div class="gmail_quote"><div dir="ltr">On Mon, Oct 29, 2018 at 11:23 PM Craig Cook via TriEmbed <<a href="mailto:triembed@triembed.org">triembed@triembed.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Since I can't upload pictures here, you should be able to see some here: <a href="https://drive.google.com/open?id=1qrpDKCUUwSSoPdv_TVqjslM3eq2wf0U_" rel="noreferrer" target="_blank">https://drive.google.com/open?id=1qrpDKCUUwSSoPdv_TVqjslM3eq2wf0U_</a><br>
<br>
I think the suggestion is the red wire goes to a heating coil using 110 Volts.  The black wire coming back into the motor (that drives the fan) has been dropped to around 16 Volts.<br>
<br>
I need a way to disconnect the heater coil and control it. That's where the solid state relay S216S02 comes in. One side will have 110V, the other receives a signal from the Arduino telling it to turn on and off.<br>
<br>
I also need to disconnect the fan motor and drive it using the Arduino. That's where I need an independent 16V applied to the fan motor.<br>
<br>
Actually, given I am only dealing with 110V, is there a better solid state relay choice?<br>
<br>
I have some of these "IRF510N IRF510 Power MOSFET N-Channel 5.6A 100V" Can I use one for the heater coil and another for the fan motor?<br>
<br>
I also have some of these "039N04L MOSFET"<br>
<br>
Thanks<br>
<br>
Craig<br>
<br>
_______________________________________________<br>
Triangle, NC Embedded Computing mailing list<br>
<br>
To post message: <a href="mailto:TriEmbed@triembed.org" target="_blank">TriEmbed@triembed.org</a><br>
List info: <a href="http://mail.triembed.org/mailman/listinfo/triembed_triembed.org" rel="noreferrer" target="_blank">http://mail.triembed.org/mailman/listinfo/triembed_triembed.org</a><br>
TriEmbed web site: <a href="http://TriEmbed.org" rel="noreferrer" target="_blank">http://TriEmbed.org</a><br>
To unsubscribe, click link and send a blank message: mailto:<a href="mailto:unsubscribe-TriEmbed@bitser.net" target="_blank">unsubscribe-TriEmbed@bitser.net</a>?subject=unsubscribe<br>
<br>
</blockquote></div>