<p dir="ltr">Thanks for the tips, Rick. Maybe I'll give the existing board another try. Sounds like I just didn't get a good joint. </p>
<div class="gmail_quote">On Nov 21, 2015 9:02 AM, "Rick via TriEmbed" <<a href="mailto:triembed@triembed.org">triembed@triembed.org</a>> wrote:<br type="attribution"><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
  
    
  
  <div bgcolor="#FFFFFF" text="#000000">
    Good morning Nick,<br>
    <br>
    <br>
    These may help you out:<br>
    <br>
<a href="http://www.allelectronics.com/make-a-store/category/455/perf-boards/1.html" target="_blank">http://www.allelectronics.com/make-a-store/category/455/perf-boards/1.html</a><br>
    <br>
    <a href="http://www.mpja.com/Protoboards/products/284/" target="_blank">http://www.mpja.com/Protoboards/products/284/</a><br>
    <br>
    <a href="http://www.goldmine-elec-products.com/products.asp?dept=1293" target="_blank">http://www.goldmine-elec-products.com/products.asp?dept=1293</a><br>
    <br>
    <br>
    Your solder joint pulling off the board could be an issue with
    insufficient heat. If there is a lot of copper, you need a large
    heat mass to heat the copper and solder to create a good solder
    joint. Also, after you clean off the solder mask, polish the copper
    just a bit, and then apply rosin flux and pre-tin the solder
    connection points before soldering the wires.<br>
    <br>
    If you can make use of an existing connection to the copper trace of
    choice, you'll have an easier time (no solder mask removal, no
    tinning required).<br>
    <br>
    Cutting FR-4 is easy with sheet metal tools, but it is tough on
    material (glass strands imbedded in a polyester resin). I've used a
    metal blade in a jig saw, tin snips, a sheet metal shear, dremel
    tools, and my CNC router. You can also scribe score lines and snap
    with the scribe line on a hard surface ... a piece of steel angle
    can be a good scribing AND snapping guide. Make several passes with
    a sharp blade before snapping. <br>
    <br>
    If you have access to a tile wet saw, that would be a quick and easy
    tool to use for cutting large stuff down to size, but the kerf is a
    bit large. Water keeps the dust under control. <br>
    <br>
    The tan colored pc board material is paper phenolic ... compressed
    paper impregnated with a phenolic resin. This material is not as
    hard on tools, but is more brittle and may shatter in a shear.<br>
    <br>
    Good luck with your project.<br>
    <br>
    Regards,<br>
    <br>
    Rick<br>
    <br>
    <br>
    <br>
    <div>On 11/20/2015 10:23 PM, Nick Meyer via
      TriEmbed wrote:<br>
    </div>
    <blockquote type="cite">
      <div dir="ltr">Hi all,
        <div><br>
        </div>
        <div>I'm making some modifications to a circuit board from an
          old video game controller.  Originally I was going to scrape
          the solder mask off certain spots so I can attach the wires I
          need.  When I attempted this, I wasn't able to get a good join
          (without much force the joint broke off the board).</div>
        <div><br>
        </div>
        <div>So, now I'm thinking to get a piece of prototyping board
          with through holes.  I need roughly 12cm x 4cm pieces.  I'm
          thinking to buy a larger piece and cut multiple 12x4 pieces.</div>
        <div><br>
        </div>
        <div>Any suggestions for places to buy these?  Amazon has a lot
          of options and Mouser has a lot of options.  I'm not really
          sure what the differences are.</div>
        <div><br>
        </div>
        <div>Any help would be greatly appreciated!</div>
        <div><br>
        </div>
        <div>Thanks,</div>
        <div>Nick</div>
      </div>
      <br>
      <fieldset></fieldset>
      <br>
      <pre>_______________________________________________
Triangle, NC Embedded Computing mailing list
<a href="mailto:TriEmbed@triembed.org" target="_blank">TriEmbed@triembed.org</a>
<a href="http://mail.triembed.org/mailman/listinfo/triembed_triembed.org" target="_blank">http://mail.triembed.org/mailman/listinfo/triembed_triembed.org</a>
TriEmbed web site: <a href="http://TriEmbed.org" target="_blank">http://TriEmbed.org</a>
</pre>
    </blockquote>
    <br>
  </div>

<br>_______________________________________________<br>
Triangle, NC Embedded Computing mailing list<br>
<a href="mailto:TriEmbed@triembed.org">TriEmbed@triembed.org</a><br>
<a href="http://mail.triembed.org/mailman/listinfo/triembed_triembed.org" rel="noreferrer" target="_blank">http://mail.triembed.org/mailman/listinfo/triembed_triembed.org</a><br>
TriEmbed web site: <a href="http://TriEmbed.org" rel="noreferrer" target="_blank">http://TriEmbed.org</a><br>
<br></blockquote></div>