<html><head><meta http-equiv="Content-Type" content="text/html charset=utf-8"></head><body style="word-wrap: break-word; -webkit-nbsp-mode: space; -webkit-line-break: after-white-space;" class="">Shane, <div class=""><br class=""></div><div class="">Thank you for taking a look - I know the dimensions for this part are a little different than the standard SOIC as it seems the package body is smaller and the legs are more extended. I created my footprint to match the data sheet not the standards SOIC - Looking at this though, it seems that both would likely work.</div><div class=""><br class=""></div><div class="">As for extending the pads, Pete and I experimented with this when we were learning how to solder QFN devices and they lead to issues with bridging - perhaps worth a look here as the pins are more spaced out.</div><div class=""><br class=""></div><div class="">From what I can see, from the Power FET design image you shared <a href="http://triembed.org/lib/PowerFetSOIC8-1/PowerFetSOIC8-1-brd.png" class="">here</a>, I don’t need to connect any pins on the footprint but will add some big “pours” when I lay out the board. I am thinking this is most important for the high-side P MOSFET switch that will switch on and off the supply to the test-section of the board. </div><div class=""><br class=""></div><div class="">I will create a second part in the library for the N-MOSFET for the other part you recommended on your blog. Thanks again for helping us mere mortals comprehend the power and wonder of these devices. Drawing that MOSFET device in EAGLE is a pain but, I think it helps..</div><div class=""><br class=""></div><div class="">Chip</div><div class=""><br class=""></div><div class=""><br class=""></div><div class=""><br class=""><div><blockquote type="cite" class=""><div class="">On Jun 25, 2015, at 2:09 PM, Shane Trent <<a href="mailto:shanedtrent@gmail.com" class="">shanedtrent@gmail.com</a>> wrote:</div><br class="Apple-interchange-newline"><div class=""><div dir="ltr" class="">Chip,<div class=""><br class=""></div><div class="">Great idea on building and sharing devices for Eagle. I would like to get better at this myself. I have a bunch of old designs that will not open in Eagle 7 because of a glitch with some device definitions I built and used in the older version of Eagle (5 something). Perhaps there would be an interest in getting a few people together to share ideas/experiences on defining new parts.</div><div class=""><br class=""></div><div class="">For comparison to your P-FET device, I dropped in the only SOIC I found in my Eagle resources, the NDS8434 N-FET from SparkFun-DescreteSemi. The image below shows both devices on a schematic and a board. I like how your device shows the intrinsic body diode (it's easy to forget about it). It looks like the SparkFun footprint includes longer pads which I would THINK would give you more room for margin of error on your solder paste and placement. But you and Pete have much more experience with working with SMD parts. </div><div class=""><br class=""></div><div class=""><span id="cid:ii_14e2be5a4adf2c6e"><SOIC Footprint.jpg></span><br class=""></div><div class=""><br class=""></div><div class="">I am not sure about joining the common Drain pins or the common Source pins. Even the high-current 7-pin MOSFETs (like IRF2804S-7) appear to have separate pads for each pin on their footprint. I presume joining the common pins and adding heat spreading copper under the device are left to design choices during board layout. </div><div class=""><a href="http://www.irf.com/product-info/datasheets/data/irf2804s-7p.pdf" class="">http://www.irf.com/product-info/datasheets/data/irf2804s-7p.pdf</a><br class=""></div><div class=""><br class=""></div><div class="">On a related note, does anyone know if there is a thermal advantage to connecting heat spreading copper under an SOIC device to the Source verses the Drain? Does one work better than the other or does it make no difference?</div><div class=""><br class=""></div><div class="">Shane</div></div><div class="gmail_extra"><br class=""><div class="gmail_quote">On Thu, Jun 25, 2015 at 10:29 AM, Chip McClelland via TriEmbed <span dir="ltr" class=""><<a href="mailto:triembed@triembed.org" target="_blank" class="">triembed@triembed.org</a>></span> wrote:<br class=""><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div style="word-wrap:break-word" class="">To all, <div class=""><br class=""></div><div class="">Sorry for not getting this right on the first two attempts. <a href="https://www.dropbox.com/sh/9qdzturvffr66do/AAAv0D0bogqsjLA9GiF5-DD6a?dl=0" target="_blank" class="">Here is a link</a> to my dropbox where the PDF and the EAGLE custom MOSFET library are stored: </div><div class=""><br class=""></div><div class="">Also, I am toying with the idea of contributing some of my custom footrprints to this ambitious project to share footprints for surface mount parts.- <a href="http://www.snapeda.com/home" target="_blank" class="">SnapEDA</a> So far, I have not been impressed with the designs I have seen but, it could grow up to be a cool solution and reduce the amount of time I have to spend designing custom libraries like the one linked to above. </div><div class=""><br class=""></div><div class="">Thanks,</div><div class=""><br class=""></div><div class="">Chip</div><div class=""><br class=""></div><div class=""><div class=""><blockquote type="cite" class=""><div class="">On Jun 25, 2015, at 10:20 AM, <a href="mailto:triembed-request@triembed.org" target="_blank" class="">triembed-request@triembed.org</a> wrote:</div><br class=""><div class="">Send TriEmbed mailing list submissions to<br class=""><span style="white-space:pre-wrap" class=""> </span><a href="mailto:triembed@triembed.org" target="_blank" class="">triembed@triembed.org</a><br class=""><br class="">To subscribe or unsubscribe via the World Wide Web, visit<br class=""><span style="white-space:pre-wrap" class=""> </span><a href="http://mail.triembed.org/mailman/listinfo/triembed_triembed.org" target="_blank" class="">http://mail.triembed.org/mailman/listinfo/triembed_triembed.org</a><br class="">or, via email, send a message with subject or body 'help' to<br class=""><span style="white-space:pre-wrap" class=""> </span><a href="mailto:triembed-request@triembed.org" target="_blank" class="">triembed-request@triembed.org</a><br class=""><br class="">You can reach the person managing the list at<br class=""><span style="white-space:pre-wrap" class=""> </span><a href="mailto:triembed-owner@triembed.org" target="_blank" class="">triembed-owner@triembed.org</a><br class=""><br class="">When replying, please edit your Subject line so it is more specific<br class="">than "Re: Contents of TriEmbed digest..."<br class=""><br class=""><br class="">Today's Topics:<br class=""><br class=""> 1. Re: TriEmbed Digest, Vol 25, Issue 42 (Chip McClelland)<br class=""><br class=""><br class="">----------------------------------------------------------------------<br class=""><br class="">Message: 1<br class="">Date: Thu, 25 Jun 2015 10:20:08 -0400<br class="">From: Chip McClelland <<a href="mailto:chip@mcclellands.org" target="_blank" class="">chip@mcclellands.org</a>><br class="">To: <a href="mailto:triembed@triembed.org" target="_blank" class="">triembed@triembed.org</a><br class="">Subject: Re: [TriEmbed] TriEmbed Digest, Vol 25, Issue 42<br class="">Message-ID: <<a href="mailto:C5FEC22C-496D-42FC-BCFC-49CAA530C1EF@mcclellands.org" target="_blank" class="">C5FEC22C-496D-42FC-BCFC-49CAA530C1EF@mcclellands.org</a>><br class="">Content-Type: text/plain; charset="us-ascii"<br class=""><br class="">Shane and Pete and all, <br class=""><br class="">Thank you for the recommendations on the Surface Mount MOSFETS. Since they were not in EAGLE, I have started creating a custom library for each part. Here is the MOSFET library where I have made the first part (IRF9310P) and will add the N-MOSFET next. Please take a look and let me know if I should do something differently, For example, should I have just one continuous PAD across all the source and drain pins? I figured using a custom footprint rather than the standard SOIC-8 would allow for some better connection or thermal tweaks.<br class=""><br class="">Thanks,<br class=""><br class="">Chip<br class=""><br class="">Here is a link to the data sheet I used to define the footprint - <a href="http://www.irf.com/product-info/datasheets/data/irf9310pbf.pdf" target="_blank" class="">http://www.irf.com/product-info/datasheets/data/irf9310pbf.pdf</a> <<a href="http://www.irf.com/product-info/datasheets/data/irf9310pbf.pdf" target="_blank" class="">http://www.irf.com/product-info/datasheets/data/irf9310pbf.pdf</a>><br class=""><br class=""><br class=""><blockquote type="cite" class="">On Jun 24, 2015, at 1:00 PM, <a href="mailto:triembed-request@triembed.org" target="_blank" class="">triembed-request@triembed.org</a> wrote:<br class=""><br class="">Send TriEmbed mailing list submissions to<br class=""><span style="white-space:pre-wrap" class=""> </span><a href="mailto:triembed@triembed.org" target="_blank" class="">triembed@triembed.org</a><br class=""><br class="">To subscribe or unsubscribe via the World Wide Web, visit<br class=""><span style="white-space:pre-wrap" class=""> </span><a href="http://mail.triembed.org/mailman/listinfo/triembed_triembed.org" target="_blank" class="">http://mail.triembed.org/mailman/listinfo/triembed_triembed.org</a><br class="">or, via email, send a message with subject or body 'help' to<br class=""><span style="white-space:pre-wrap" class=""> </span><a href="mailto:triembed-request@triembed.org" target="_blank" class="">triembed-request@triembed.org</a><br class=""><br class="">You can reach the person managing the list at<br class=""><span style="white-space:pre-wrap" class=""> </span><a href="mailto:triembed-owner@triembed.org" target="_blank" class="">triembed-owner@triembed.org</a><br class=""><br class="">When replying, please edit your Subject line so it is more specific<br class="">than "Re: Contents of TriEmbed digest..."<br class=""><br class=""><br class="">Today's Topics:<br class=""><br class=""> 1. Re: Recommended SMD Logic-Level MOSFETs for prototyping<br class=""> (Shane Trent)<br class=""> 2. iOS developer needed part-time (Jon Wolfe)<br class=""> 3. Re: iOS developer needed part-time (Robert Gasiorowski)<br class=""><br class=""><br class="">----------------------------------------------------------------------<br class=""><br class="">Message: 1<br class="">Date: Tue, 23 Jun 2015 15:52:39 -0400<br class="">From: Shane Trent <<a href="mailto:shanedtrent@gmail.com" target="_blank" class="">shanedtrent@gmail.com</a>><br class="">To: Pete Soper <<a href="mailto:pete@soper.us" target="_blank" class="">pete@soper.us</a>><br class="">Cc: TriEmbed Discussion <<a href="mailto:triembed@triembed.org" target="_blank" class="">triembed@triembed.org</a>><br class="">Subject: Re: [TriEmbed] Recommended SMD Logic-Level MOSFETs for<br class=""><span style="white-space:pre-wrap" class=""> </span>prototyping<br class="">Message-ID:<br class=""><span style="white-space:pre-wrap" class=""> </span><<a href="mailto:CAAFjd3ps%2B0LewCRG17EnKu1MqksoPiXDE0ank8Cj3sB0MVN4SQ@mail.gmail.com" target="_blank" class="">CAAFjd3ps+0LewCRG17EnKu1MqksoPiXDE0ank8Cj3sB0MVN4SQ@mail.gmail.com</a>><br class="">Content-Type: text/plain; charset="utf-8"<br class=""><br class="">Pete,<br class=""><br class="">I like the board. I think a library of helper boards could be helpful for<br class="">prototyping. The engineers at Pololu have the best examples I have seen for<br class="">high-current PCB layout with surface mount MOSFETS. This board uses SOIC8<br class="">transistors in a motor driver H-bridge rated for 18 volts and 15 amps. I<br class="">like their multipurpose details on the high-current terminals. They use all<br class="">the copper they can for the terminal pads while allowing the use of screw<br class="">terminals or direct soldering of two different sizes of wire. Beautiful<br class="">design.<br class=""><br class=""><a href="https://www.pololu.com/product/755" target="_blank" class="">https://www.pololu.com/product/755</a><br class="">Top image - <a href="https://www.pololu.com/picture/view/0J1025" target="_blank" class="">https://www.pololu.com/picture/view/0J1025</a><br class="">Bottom image - <a href="https://www.pololu.com/picture/view/0J1026" target="_blank" class="">https://www.pololu.com/picture/view/0J1026</a><br class=""><br class="">Shane<br class=""><br class="">On Tue, Jun 23, 2015 at 1:45 PM, Pete Soper via TriEmbed <<br class=""><a href="mailto:triembed@triembed.org" target="_blank" class="">triembed@triembed.org</a>> wrote:<br class=""><br class=""><blockquote type="cite" class="">Great writeup.<br class="">I found myself searching for "beefy breakouts" for SOIC-8 packages and<br class="">couldn't find one. I just knocked this out in Eagle and would like comments<br class="">or criticism:<br class=""><br class=""> <a href="http://triembed.org/images/b1.png" target="_blank" class="">http://triembed.org/images/b1.png</a><br class=""><br class="">(the Eagle files are the same URL but ending FAT-SOIC8.{brd,sch})<br class=""><br class="">This is a dead-simple board except there are redundant traces on the<br class="">bottom to vias that are in turn connected to the chip pads. So there are<br class="">two .024" traces for each pin. The vias have relatively large holes I<br class="">guestimate to have a circumference three times the trace width.<br class=""><br class="">The biggest question is whether this is redundant. If there's an<br class="">unburdened Eagle file out there that I could upload to OSHPark I might be<br class="">able to get some boards made in time for the next meeting. This board would<br class="">cost 47 cents. But the boards I've found so far online have laughably<br class="">narrow traces for multiple amps.<br class=""><br class="">I notice that the N channel chip you point to can handle pulses over 100<br class="">amperes. Wow.<br class=""><br class="">-Pete<br class="">PS Is just crazy some times. A fraction of the time it flagged net<br class="">connections when I added wires from the via chip pads or else refused to<br class="">acknowledge the connection. So I'm only 92% sure there would be copper in<br class="">some cases and the first version of this board might really only have<br class="">single traces for some of the pins.<br class=""><br class=""><br class="">On 06/23/2015 11:22 AM, Shane Trent via TriEmbed wrote:<br class=""><br class="">Someone else asked for recommendations on logic-level MOSFETs so I wrote<br class="">it up as a blog post.<br class=""><br class=""><br class=""><a href="http://fettricks.blogspot.com/2015/06/prototype-friendly-smd-logic-level.html" target="_blank" class="">http://fettricks.blogspot.com/2015/06/prototype-friendly-smd-logic-level.html</a><br class=""><br class=""><br class="">Shane<br class=""><br class="">--<br class="">A blog about some of my projects. <a href="http://fettricks.blogspot.com/" target="_blank" class="">http://fettricks.blogspot.com/</a><br class=""><br class=""><br class="">_______________________________________________<br class="">Triangle, NC Embedded Computing mailing <a href="mailto:listTriEmbed@triembed.orghttp" class="">listTriEmbed@triembed.orghttp</a>://<a href="http://mail.triembed.org/mailman/listinfo/triembed_triembed.org" target="_blank" class="">mail.triembed.org/mailman/listinfo/triembed_triembed.org</a><br class="">TriEmbed web site: <a href="http://triembed.org/" target="_blank" class="">http://TriEmbed.org</a><br class=""><br class=""><br class=""><br class="">_______________________________________________<br class="">Triangle, NC Embedded Computing mailing list<br class=""><a href="mailto:TriEmbed@triembed.org" target="_blank" class="">TriEmbed@triembed.org</a><br class=""><a href="http://mail.triembed.org/mailman/listinfo/triembed_triembed.org" target="_blank" class="">http://mail.triembed.org/mailman/listinfo/triembed_triembed.org</a><br class="">TriEmbed web site: <a href="http://triembed.org/" target="_blank" class="">http://TriEmbed.org</a><br class=""><br class=""><br class=""></blockquote><br class=""><br class="">-- <br class="">A blog about some of my projects. <a href="http://fettricks.blogspot.com/" target="_blank" class="">http://fettricks.blogspot.com/</a><br class="">-------------- next part --------------<br class="">An HTML attachment was scrubbed...<br class="">URL: <<a href="http://mail.triembed.org/pipermail/triembed_triembed.org/attachments/20150623/92d50738/attachment-0001.html" target="_blank" class="">http://mail.triembed.org/pipermail/triembed_triembed.org/attachments/20150623/92d50738/attachment-0001.html</a>><br class=""><br class="">------------------------------<br class=""><br class="">Message: 2<br class="">Date: Tue, 23 Jun 2015 18:15:17 -0400<br class="">From: Jon Wolfe <<a href="mailto:jonjwolfe@anibit.com" target="_blank" class="">jonjwolfe@anibit.com</a>><br class="">To: TriEmbed Discussion <<a href="mailto:triembed@triembed.org" target="_blank" class="">triembed@triembed.org</a>><br class="">Subject: [TriEmbed] iOS developer needed part-time<br class="">Message-ID: <<a href="mailto:42515d35b99fbe8b0a406aee87154f72@anibit.com" target="_blank" class="">42515d35b99fbe8b0a406aee87154f72@anibit.com</a>><br class="">Content-Type: text/plain; charset="us-ascii"<br class=""><br class=""><br class=""><br class="">This isn't embedded electronics related, so if you aren't into iOS, you<br class="">can stop reading now ;) <br class=""><br class="">I alluded to it at the last meeting, but things are starting to<br class="">solidify, and it looks like I'm going to need to hire an iOS developer. <br class=""><br class="">If you are interested in some part time or side work developing an<br class="">iPhone app. Let me know. It's a pretty straightforward app, a few forms<br class="">and menus, that uses REST calls to interact with a server, with possibly<br class="">some camera and SMS interaction. There's no graphics programming needed.<br class="">I will have the server side component and an Android version developed<br class="">in tandem. <br class=""><br class="">I'm still working out a few details, such as rates, timeline, etc, but I<br class="">would prefer someone local to RTP that I could meet with on occasion.<br class="">You would need to provide your own equipment for development. <br class=""><br class="">Anyways, if you have any interest, contact me. <br class=""><br class="">Now back to your regularly scheduled program :) <br class="">-- <br class=""><br class="">Jon Wolfe<br class="">Anibit Technology LLC.<br class=""><br class=""><a href="https://anibit.com/" target="_blank" class="">https://anibit.com</a><br class=""><br class=""><br class="">-------------- next part --------------<br class="">An HTML attachment was scrubbed...<br class="">URL: <<a href="http://mail.triembed.org/pipermail/triembed_triembed.org/attachments/20150623/8a29eb17/attachment-0001.html" target="_blank" class="">http://mail.triembed.org/pipermail/triembed_triembed.org/attachments/20150623/8a29eb17/attachment-0001.html</a>><br class=""><br class="">------------------------------<br class=""><br class="">Message: 3<br class="">Date: Tue, 23 Jun 2015 21:09:04 -0400<br class="">From: Robert Gasiorowski <<a href="mailto:rgresume@gmail.com" target="_blank" class="">rgresume@gmail.com</a>><br class="">To: Jon Wolfe <<a href="mailto:jonjwolfe@anibit.com" target="_blank" class="">jonjwolfe@anibit.com</a>><br class="">Cc: TriEmbed Discussion <<a href="mailto:triembed@triembed.org" target="_blank" class="">triembed@triembed.org</a>><br class="">Subject: Re: [TriEmbed] iOS developer needed part-time<br class="">Message-ID:<br class=""><span style="white-space:pre-wrap" class=""> </span><CAEU50hXPUoEuycAsJKLTe=<a href="mailto:OoBSHi3i%2BgJ_UMOKp6a%2B2H24SucQ@mail.gmail.com" target="_blank" class="">OoBSHi3i+gJ_UMOKp6a+2H24SucQ@mail.gmail.com</a>><br class="">Content-Type: text/plain; charset="utf-8"<br class=""><br class="">Have you considered using Ionic/Cordova to develop your mobile apps? You<br class="">develop one app and build/deploy to multiple platforms.<br class=""><br class="">In any case, I would love to get involved in your project, but I am not<br class="">sure I will have enough time to spare.<br class=""><br class="">Rob.<br class=""><br class="">On Tue, Jun 23, 2015 at 6:15 PM, Jon Wolfe via TriEmbed <<br class=""><a href="mailto:triembed@triembed.org" target="_blank" class="">triembed@triembed.org</a>> wrote:<br class=""><br class=""><blockquote type="cite" class=""><br class=""><br class="">This isn't embedded electronics related, so if you aren't into iOS, you<br class="">can stop reading now ;)<br class=""><br class=""><br class=""><br class="">I alluded to it at the last meeting, but things are starting to solidify,<br class="">and it looks like I'm going to need to hire an iOS developer.<br class=""><br class="">If you are interested in some part time or side work developing an iPhone<br class="">app. Let me know. It's a pretty straightforward app, a few forms and menus,<br class="">that uses REST calls to interact with a server, with possibly some camera<br class="">and SMS interaction. There's no graphics programming needed. I will have<br class="">the server side component and an Android version developed in tandem.<br class=""><br class="">I'm still working out a few details, such as rates, timeline, etc, but I<br class="">would prefer someone local to RTP that I could meet with on occasion. You<br class="">would need to provide your own equipment for development.<br class=""><br class="">Anyways, if you have any interest, contact me.<br class=""><br class="">Now back to your regularly scheduled program :)<br class="">--<br class=""><br class="">Jon Wolfe<br class="">Anibit Technology LLC.<br class=""><a href="https://anibit.com/" target="_blank" class="">https://anibit.com</a><br class=""><br class=""><br class="">_______________________________________________<br class="">Triangle, NC Embedded Computing mailing list<br class=""><a href="mailto:TriEmbed@triembed.org" target="_blank" class="">TriEmbed@triembed.org</a><br class=""><a href="http://mail.triembed.org/mailman/listinfo/triembed_triembed.org" target="_blank" class="">http://mail.triembed.org/mailman/listinfo/triembed_triembed.org</a><br class="">TriEmbed web site: <a href="http://triembed.org/" target="_blank" class="">http://TriEmbed.org</a><br class=""><br class=""><br class=""></blockquote>-------------- next part --------------<br class="">An HTML attachment was scrubbed...<br class="">URL: <<a href="http://mail.triembed.org/pipermail/triembed_triembed.org/attachments/20150623/d2232ccb/attachment-0001.html" target="_blank" class="">http://mail.triembed.org/pipermail/triembed_triembed.org/attachments/20150623/d2232ccb/attachment-0001.html</a>><br class=""><br class="">------------------------------<br class=""><br class="">Subject: Digest Footer<br class=""><br class="">_______________________________________________<br class="">TriEmbed mailing list<br class=""><a href="mailto:TriEmbed@triembed.org" target="_blank" class="">TriEmbed@triembed.org</a><br class=""><a href="http://mail.triembed.org/mailman/listinfo/triembed_triembed.org" target="_blank" class="">http://mail.triembed.org/mailman/listinfo/triembed_triembed.org</a><br class=""><br class=""><br class="">------------------------------<br class=""><br class="">End of TriEmbed Digest, Vol 25, Issue 42<br class="">****************************************<br class=""></blockquote><br class="">-------------- next part --------------<br class="">An HTML attachment was scrubbed...<br class="">URL: <<a href="http://mail.triembed.org/pipermail/triembed_triembed.org/attachments/20150625/dff84061/attachment.html" target="_blank" class="">http://mail.triembed.org/pipermail/triembed_triembed.org/attachments/20150625/dff84061/attachment.html</a>><br class="">-------------- next part --------------<br class="">A non-text attachment was scrubbed...<br class="">Name: MOSFETs.lbr<br class="">Type: application/octet-stream<br class="">Size: 10686 bytes<br class="">Desc: not available<br class="">URL: <<a href="http://mail.triembed.org/pipermail/triembed_triembed.org/attachments/20150625/dff84061/attachment.obj" target="_blank" class="">http://mail.triembed.org/pipermail/triembed_triembed.org/attachments/20150625/dff84061/attachment.obj</a>><br class="">-------------- next part --------------<br class="">An HTML attachment was scrubbed...<br class="">URL: <<a href="http://mail.triembed.org/pipermail/triembed_triembed.org/attachments/20150625/dff84061/attachment-0001.html" target="_blank" class="">http://mail.triembed.org/pipermail/triembed_triembed.org/attachments/20150625/dff84061/attachment-0001.html</a>><br class=""><br class="">------------------------------<br class=""><br class="">Subject: Digest Footer<br class=""><br class="">_______________________________________________<br class="">TriEmbed mailing list<br class=""><a href="mailto:TriEmbed@triembed.org" target="_blank" class="">TriEmbed@triembed.org</a><br class=""><a href="http://mail.triembed.org/mailman/listinfo/triembed_triembed.org" target="_blank" class="">http://mail.triembed.org/mailman/listinfo/triembed_triembed.org</a><br class=""><br class=""><br class="">------------------------------<br class=""><br class="">End of TriEmbed Digest, Vol 25, Issue 43<br class="">****************************************<br class=""></div></blockquote></div><br class=""></div></div><br class="">_______________________________________________<br class="">
Triangle, NC Embedded Computing mailing list<br class="">
<a href="mailto:TriEmbed@triembed.org" class="">TriEmbed@triembed.org</a><br class="">
<a href="http://mail.triembed.org/mailman/listinfo/triembed_triembed.org" rel="noreferrer" target="_blank" class="">http://mail.triembed.org/mailman/listinfo/triembed_triembed.org</a><br class="">
TriEmbed web site: <a href="http://triembed.org/" rel="noreferrer" target="_blank" class="">http://TriEmbed.org</a><br class="">
<br class=""></blockquote></div><br class=""><br clear="all" class=""><div class=""><br class=""></div>-- <br class=""><div class="gmail_signature"><div dir="ltr" class=""><span style="font-family: HelveticaNeue-Light, 'Helvetica Neue Light', 'Helvetica Neue', Helvetica, Arial, 'Lucida Grande', sans-serif; font-size: 16px;" class="">A blog about some of my projects. <a href="http://fettricks.blogspot.com/" target="_blank" class="">http://fettricks.blogspot.com/</a></span><br class=""></div></div>
</div>
</div></blockquote></div><br class=""></div></body></html>