<div dir="ltr">Martin,<div><br></div><div>The Digikey search engine points to this as the lowest Rds (100 mOhm at Fgs=5V) N-FET in a 4-pin DIP package ($1 for 1). At the rated 2.5 amps it would be dissipating 0.63 Watts which sounds like a challenge on a breadboard but feasible on a PCB with some extra copper for spreading the heat. </div><div><a href="http://www.digikey.com/product-detail/en/IRLD024PBF/IRLD024PBF-ND/812492">http://www.digikey.com/product-detail/en/IRLD024PBF/IRLD024PBF-ND/812492</a><br></div><div><br></div><div>You can use TO-220 or other SIP type packages on a breadboard. The Digikey search engine found this TO-251A 30V N-FET with an Rds of 3.2 mOhms at Vgs=4.5V, $0.81 for 1. The power dissipation should be very low until you have well exceeded the current carrying capacity of your breadboard (0.08W at 5 amps).</div><div><a href="http://www.digikey.com/product-detail/en/AOI510/785-1487-1-ND/3603498">http://www.digikey.com/product-detail/en/AOI510/785-1487-1-ND/3603498</a><br></div><div><br></div><div>Super low Rds in through-hole P-FET is much tougher. They get pricey fast. This is the best bang for the buck P-FET I could find, -30V part, Rds = 10 mOhms at Vgs=-5V, $2.90 for 1. (0.25 Watts at 5 amps). </div><div><a href="http://www.digikey.com/product-detail/en/SUP53P06-20-E3/SUP53P06-20-E3-ND/2623103">http://www.digikey.com/product-detail/en/SUP53P06-20-E3/SUP53P06-20-E3-ND/2623103</a><br></div><div><br></div><div>Generally at TO-220 can dissipate around 1W without a heat-sink in free-air without damage.</div><div><br></div><div>Shane</div><div><br></div><div><br></div></div><div class="gmail_extra"><br><div class="gmail_quote">On Tue, Jun 23, 2015 at 2:12 PM, Martin Brooke via TriEmbed <span dir="ltr"><<a href="mailto:triembed@triembed.org" target="_blank">triembed@triembed.org</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr"><div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif;font-size:small">​I would like your thoughts on <b>non-SMT</b> Logic Level MOSFETs that can plug into a protoboard.</div><br></div><div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif;font-size:small">​I have been using:​</div></div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif;font-size:small"><br></div><div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif;font-size:small">​NMOS​  <a href="http://www.digikey.com/product-detail/en/IRL2703PBF/IRL2703PBF-ND/811700" style="font-family:arial,sans-serif" target="_blank">IRL2703PBF</a><div class="gmail_default" style="display:inline">​  $1.74 for 1​ and </div>​PMOS​ <a href="http://www.digikey.com/product-search/en?vendor=0&keywords=IRLIB9343PBF" style="font-family:arial,sans-serif" target="_blank">IRLIB9343PBF</a><div class="gmail_default" style="display:inline">​ $1.37 for 1​, they are quite similar in performance.</div></div></div><div><font face="arial, helvetica, sans-serif"><br></font></div><div><font face="arial, helvetica, sans-serif"><div class="gmail_default" style="display:inline">​These will fit (with a shove) in a regular protoboard and can carry a lot of current .  So they have been sort of a work horse for just boosting a microcontrollers switching capability to drive a motor or other high current device quickly.</div></font></div><div><font face="arial, helvetica, sans-serif"><br></font></div><div><font face="arial, helvetica, sans-serif"><div class="gmail_default" style="display:inline">​But is seems there should be better devices.  The above devices tend to be overkill in current and a 4-DIP or 6-DIP package would be much nicer.  But everything I have found had too high a threshold voltage PMOS for logic control. I would like a similar NMOS and PMOS at least for threshold voltage magnitude (around 1-2V) and package type.  </div></font><span style="font-family:arial,helvetica,sans-serif"> If I could find some around 100mA to 1A it would be ideal I think.</span></div><div><br></div><div><div><font face="arial, helvetica, sans-serif"><div class="gmail_default" style="font-family:arial,helvetica,sans-serif;font-size:small;display:inline">​I found this nice 4-DIP NMOS ​</div><a href="http://www.digikey.com/product-detail/en/IRLD120PBF/IRLD120PBF-ND/812490" target="_blank">IRLD120PBF</a><div class="gmail_default" style="font-family:arial,helvetica,sans-serif;font-size:small;display:inline">​, for $.76 and w</div></font><div class="gmail_default" style="font-family:arial,helvetica,sans-serif;display:inline">e have been using this similar 4-DIP NMOS </div><a href="http://www.digikey.com/product-detail/en/IRLD014PBF/IRLD014PBF-ND/812481" style="font-family:arial,helvetica,sans-serif" target="_blank">IRLD014PBF</a><div class="gmail_default" style="font-family:arial,helvetica,sans-serif;display:inline">​ for $.92 for a few years, I just wish there was a PMOS like them.</div></div><div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif;display:inline">​</div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif;display:inline">​</div></div></div><div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif;display:inline">This pair of NMOS and PMOS in a 8-DIP <a href="http://www.digikey.com/product-detail/en/ALD1115PAL/1014-1044-ND/2414320" target="_blank">ALD1115PAL</a> for  $2.02 looks OK but they are too low current (few mA) to be useful.</div></div><div><font face="arial, helvetica, sans-serif"><br></font></div><div><font face="arial, helvetica, sans-serif"><div class="gmail_default" style="font-family:arial,helvetica,sans-serif;font-size:small;display:inline">​Not interested in BJTs for this.  Hard to beat a MOSFET ​for simplicity of drive and you can put them in parallel without resistor degeneration. </div><br></font><div class="gmail_default" style="font-family:arial,helvetica,sans-serif;font-size:small"><br></div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif;font-size:small">Cheers,</div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif;font-size:small"><br></div><div class="gmail_extra"><div><div dir="ltr"><div><div dir="ltr"><div></div></div></div></div></div>
</div></div></div>
<br>_______________________________________________<br>
Triangle, NC Embedded Computing mailing list<br>
<a href="mailto:TriEmbed@triembed.org">TriEmbed@triembed.org</a><br>
<a href="http://mail.triembed.org/mailman/listinfo/triembed_triembed.org" rel="noreferrer" target="_blank">http://mail.triembed.org/mailman/listinfo/triembed_triembed.org</a><br>
TriEmbed web site: <a href="http://TriEmbed.org" rel="noreferrer" target="_blank">http://TriEmbed.org</a><br>
<br></blockquote></div><br><br clear="all"><div><br></div>-- <br><div class="gmail_signature"><div dir="ltr"><span style="color:rgb(0,0,0);font-family:HelveticaNeue-Light,'Helvetica Neue Light','Helvetica Neue',Helvetica,Arial,'Lucida Grande',sans-serif;font-size:16px">A blog about some of my projects.  <a href="http://fettricks.blogspot.com/" target="_blank">http://fettricks.blogspot.com/</a></span><br></div></div>
</div>