<div dir="ltr"><div>You can also use either a clamp on (split) or pass through (disconnect, pass wire through sensor and reconnect) transformer to measure. Sparkfun has a 30A clamp on here: <a href="https://www.sparkfun.com/products/11005" target="_blank">https://www.sparkfun.com/products/11005</a><br><br></div>I also have a bookmark for an ElecFreaks Octopus version (pass through) but the link <br><a href="http://www.elecfreaks.com/store/octopus-noninvasive-ac-current-sensor-ta1703-brick-p-648.html">http://www.elecfreaks.com/store/octopus-noninvasive-ac-current-sensor-ta1703-brick-p-648.html</a><br>appears to be broken. I found info in their wiki about it here:<br><div><a href="http://www.elecfreaks.com/wiki/index.php?title=Octopus_Non-invasive_AC_current_sensor_%28TA12-100%29_Brick" target="_blank">http://www.elecfreaks.com/wiki/index.php?title=Octopus_Non-invasive_AC_current_sensor_%28TA12-100%29_Brick</a><br></div><div><br></div><div>These get placed around one AC hot wire and depending on the current draw, a voltage is induced that can be measured by a micro controller.<br><br></div><div>Glen<br></div></div><div class="gmail_extra"><br><div class="gmail_quote">On Wed, Jan 14, 2015 at 2:15 PM, Dwight Morgan <span dir="ltr"><<a href="mailto:dwight.w.morgan@gmail.com" target="_blank">dwight.w.morgan@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div link="blue" vlink="purple" lang="EN-US"><div><p class="MsoNormal">Hello All:<u></u><u></u></p><p class="MsoNormal"><u></u> <u></u></p><p class="MsoNormal">I want to monitor when my hot water heater is on and off using my Arduino UNO. I have done research on sensors and it looks like the best choice is the ACS712 Hall Effect Current Sensor. <u></u><u></u></p><p class="MsoNormal"><u></u> <u></u></p><p class="MsoNormal">My water heater has two 4500 Watt elements at 240 Volts. So the calculated current draw is 18.75 amps since only one element is on at a time.<u></u><u></u></p><p class="MsoNormal">My question(s): First, is the Hall Effect sensor a good choice and second, if so, will the 20 amp rated one work okay? <u></u><u></u></p><p class="MsoNormal"><u></u> <u></u></p><p class="MsoNormal">Also, if this is viable, I think I will try to use Cat5 cable to pick up the signal which will be about 100 feet away. I’m not sure exactly about the connectors yet.<u></u><u></u></p><p class="MsoNormal"><u></u> <u></u></p><p class="MsoNormal">All advice is appreciated. <u></u><u></u></p><p class="MsoNormal"><u></u> <u></u></p><p class="MsoNormal">Thanks!<span class="HOEnZb"><font color="#888888"><u></u><u></u></font></span></p><span class="HOEnZb"><font color="#888888"><p class="MsoNormal"><u></u> <u></u></p><p class="MsoNormal">Dwight<u></u><u></u></p><p class="MsoNormal"><u></u> <u></u></p><p class="MsoNormal"><u></u> <u></u></p></font></span></div></div><br>_______________________________________________<br>
Triangle, NC Embedded Computing mailing list<br>
<a href="mailto:TriEmbed@triembed.org">TriEmbed@triembed.org</a><br>
<a href="http://mail.triembed.org/mailman/listinfo/triembed_triembed.org" target="_blank">http://mail.triembed.org/mailman/listinfo/triembed_triembed.org</a><br>
TriEmbed web site: <a href="http://TriEmbed.org" target="_blank">http://TriEmbed.org</a><br>
<br></blockquote></div><br></div>