<div dir="ltr">Ok, yeah, that's what I was thinking. I wanted it to be normally open and then energize the relay to close and provide power. That way when I turn the supply on, nothing is connected by default. But I assume I still have to be worried about the contact welding in that scenario since I might already have the device drawing power hooked up (I would rather not have to disconnect it every time I start up the supply).<div>

<br></div><div>Also, I think I found my power rails: <a href="http://www.amazon.com/dp/B000H9JRI0/ref=biss_dp_t_asn">http://www.amazon.com/dp/B000H9JRI0/ref=biss_dp_t_asn</a></div><div>1/8" x 1/4" copper bar stock. My calculations show this should be able to handle WAY more power than I need. And it's pretty cheap. Figure I'd just do a slightly wider than 1/4" trace and then solder this on top.</div>

</div><div class="gmail_extra"><br><br><div class="gmail_quote">On Wed, Jul 9, 2014 at 4:19 AM, Scott Hall <span dir="ltr"><<a href="mailto:scottghall1@gmail.com" target="_blank">scottghall1@gmail.com</a>></span> wrote:<br>

<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
  
    
  
  <div bgcolor="#FFFFCC" text="#3333FF"><div class="">
    <div>On 07/08/2014 05:50 PM, Adam Haile
      wrote:<br>
    </div>
    <blockquote type="cite">
      <div dir="ltr">So,  let me make sure I understand this...
        <div>When you say have the relays energized, I know you mean
          energize the solenoid but do you mean by that that the relay
          contacts are closed (power flowing) or open (no power)? I'm
          guessing you mean don't go from open to closed while there's
          power flowing since their will be a temporary arc? Could I
          just use a normally closed relay and then use the
          microcontroller to open the relay and cut the power if I need
          to.</div>
        <div><br>
        </div>
      </div>
    </blockquote>
    <br></div>
    For safety reasons, you want the relay to disconnect if energizing
    power is removed.  An NC contacts will not break the circuit if you
    have power control problems to the energizing coil.<div class=""><br>
    <br>
    <blockquote type="cite">
      <div dir="ltr">
        <div>Do you have any links to those higher cost relays? I would
          really love to actually make it so that I could have a button
          on the front (hooked to the uC) that would allow me to, using
          the relay, turn the power on or off to any of the outputs. So
          having one of these nicer relays, if not too expensive, might
          be nice.</div>
      </div>
      <br>
    </blockquote>
    <br></div>
    Look up "contactors" for relays designed for high currents and
    regular switching.<div class=""><br>
    <br>
    <pre cols="80">-- 
Scott G. Hall
Raleigh, NC, USA
<a href="mailto:ScottGHall1@GMail.Com" target="_blank">ScottGHall1@GMail.Com</a>
</pre>
  </div></div>

<br>_______________________________________________<br>
Triangle, NC Embedded Computing mailing list<br>
<a href="mailto:TriEmbed@triembed.org">TriEmbed@triembed.org</a><br>
<a href="http://mail.triembed.org/mailman/listinfo/triembed_triembed.org" target="_blank">http://mail.triembed.org/mailman/listinfo/triembed_triembed.org</a><br>
TriEmbed web site: <a href="http://TriEmbed.org" target="_blank">http://TriEmbed.org</a><br>
<br></blockquote></div><br></div>