[TriEmbed] Driving 32 5v relays

[pete@soper.us]

Figuring that you've already bought the relays and lights, I suggest five ULN2003a relay drivers:
http://www.digikey.com/product-detail/en/ULN2003A/497-2344-5-ND/599603

Here's how to connect it (sorry about the hi-res):

https://electrosome.com/wp-content/uploads/2013/05/Interfacing-Relay-with-8051-using-ULN2003.jpg

No way will the '595 drive the relays directly if they need 73ma and, as John said, if one gate does work, trying to get several on at once  is likely to exceed the limits for the whole chip, so the per-gate capability is only part of the story. Even if it could sink the current notice you don't get a full five volts out of the chip's gate and via Ohm's law the current through the coil will be lower. 

Relay drivers will add more complexity, but the combination will work.

I agree with Robert that a triac would be the way to go from scratch for mains voltage lights, but if you already have all the relays and lights that was no doubt some significant cost.

This driver chip has internal diodes so it can handle inductive loads. An ordinary 74HC logic chip, if it could somehow handle the coil current, would be sent straight to semiconductor heaven by back EMF without a diode or RC circuit or varistor to constrain the voltage as the relay's magnetic fueld collapses (when the relay is turned off).

Oh, note this chip sinks current. So the '595 would drive an input and the corresponding output provides a ground path for the relay coil.

Finally, two more important details: The internal transustor and (yet another) diode in the driver will drop significant voltage, so for nice, reliable operation with five volt relays I strongly recommend six volts to end up with something clise to five going through the relay coils. 

Here's a wall wart that looks like it would work well:

http://www.digikey.com/product-detail/en/WSU060-3000/237-1626-ND/3105436

Also, be sure to set up the relay supply with decoupling from whatever is powering the logic. The easy way is to use a separate wall wart for the driver commons.

Pete

----- Reply message -----
From: "Richard Prevette via TriEmbed" <triembed at triembed.org>
To: "Adam Haile" <email at adamhaile.net>
Cc: "triembed at triembed.org" <TriEmbed at triembed.org>
Subject: [TriEmbed] Driving 32 5v relays
Date: Thu, Jul 16, 2015 12:10 PM

Thanks all for the comments.  Very informative.  Rodney, I wish I'd seen this board before I started but if had to buy more boards, I would look at solid state.  (I am using 4 8 channel boards.)

I found a 5v 3a wall adapter on Amazon $12.00.  Looks like that will do the job.

On Thu, Jul 16, 2015 at 10:33 AM, Richard Prevette <prevette.richard at gmail.com> wrote:
The answer the first comment is mostly money.  I am using c9 size Christmas lights for a yard display.  I have 16 PVC pips painted like candy canes with two lights per pole. 

The second comment looks like just the ticket but would it have to be wired to car battery or a 12v wall adapter with at least
a 3 amp rating?

On Thu, Jul 16, 2015 at 10:16 AM, Adam Haile <email at adamhaile.net> wrote:
Stupid question... why not just use digital LEDs?https://www.youtube.com/watch?v=_nbuSgYoCSQ
Full disclaimer: I have a tiny business that does LED lighting stuff, but I am also just a huge fan of digital LED strips since they take away complications like those with relays and such.

More on your original question... no, no... not a resistor to do 14v -> 5v! You would be dropping 9v and @ 3A be dissipating 27W!   I have bins full of buck converters like the one linked below that will do 8-23V input and output a nice steady 5V. They work great and are very efficient.

http://www.amazon.com/Nextrox%C2%AE-Display-Supply-Converter-Module/dp/B00CBCGAL8/


On Thu, Jul 16, 2015 at 11:10 AM, Richard Prevette via TriEmbed <triembed at triembed.org> wrote:

I am making a Christmas light display using 32 relays.  Using arduino and four 74HC595n shift registers. 
The relays are SRD-5vDC-SL-C.  Here is the question: I may be misunderstanding but the datasheet states each
relay takes 72ma.  I put  a meter across the power and that seems right.  At one point all relays will be on at the same time.
That looks like I need a power source that will supply about 2.3 amps.  32 x 72 x 1000 = 2.3a (Correct ?) 

I have a Dell AC adapter that states output at 14v dc and 3 amps.  All I need is a resister to lower 14 to 5 volts and 
I good to go?



_______________________________________________

Triangle, NC Embedded Computing mailing list

TriEmbed at triembed.org

http://mail.triembed.org/mailman/listinfo/triembed_triembed.org

TriEmbed web site: http://TriEmbed.org
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://mail.triembed.org/pipermail/triembed_triembed.org/attachments/20150716/6a0a4694/attachment.htm>